0760-22278043
PCB microvia back drilling technology: characteristics, challenges, and research progress

With the continuous acceleration of product iteration in the communication and electronics industry, PCB, as the "mother of electronic products", has put forward more stringent requirements for the quality of micro hole processing. Backdrilling, as a key process for removing non essential copper from through holes and controlling the length of residual piles, directly affects the integrity of high-speed signal transmission in terms of processing quality. Due to the fact that back drilling is usually carried out after through-hole metallization, there are essential differences in processing conditions compared to ordinary through-hole drilling. Issues such as hole blockage, positioning accuracy, and residual pile length control have gradually become the core challenges restricting the development of micro hole back drilling technology. Previous studies have mainly focused on application aspects such as process optimization, processing parameters, processing methods, and micro drilling structures, but there is still a lack of systematic understanding of their underlying mechanisms.

 

The particularity and key challenges of back drilling processing

 

Ordinary through-hole drilling is the process of penetrating the entire PCB, while the entire cutting edge of a micro drill is subjected to material reaction forces, resulting in a relatively continuous stress state. During the back drilling process, due to the metalization of the through-hole, there is a copper plating layer on the inner wall of the hole, and the drill tip does not participate in effective cutting. Only the cutting edges on both sides come into contact with the material, forming a locally loaded state. This asymmetric force characteristic makes the back drilling process more sensitive to hole accuracy and tool rigidity. At the same time, before drilling, the PCB needs to be re clamped and repositioned. Any slight deviation in the hole position may cause uneven force on the drill bit, resulting in a "walking" phenomenon, which can lead to hole bending or even drill breakage. Therefore, the diameter of the micro drill used for back drilling is usually 0.15 mm or more larger than the diameter of the through-hole to ensure basic positioning tolerance.

 

 

Due to the difficulty of material processing, small aperture, and large depth, high-speed board micro hole back drills have higher requirements for micro hole quality, positioning accuracy, and stub length. Specifically, back drilling faces three prominent challenges. Firstly, the drilling heat causes the resin in the high-speed board to tend to agglomerate and form high molecular weight polymers, which adhere to the surface of the micro drill, resulting in debris on the hole wall, wire entanglement on the back drill, and hole blockage problems. Among them, hole blockage is the most frequent, and the chips cannot be discharged in a timely manner, which blocks the micro holes and seriously affects the quality of signal transmission. Secondly, as the aperture decreases, the allowable hole displacement becomes smaller and smaller. Backdrilling deviation can lead to excessive stub residue, which has adverse effects on signal transmission. Thirdly, the increase in the aspect ratio of micropores makes it difficult to accurately control the depth of the back drilling. Once the back drilling is too deep, the stub and effective copper holes will be removed together, causing the micropores to lose their signal transmission function and even leading to the scrapping of the board.

 

Mechanism and Technological Countermeasures of Hole Blocking Problem

 

The essence of hole blockage is that the ability to generate drilling debris exceeds the ability to remove it. During the back drilling process, the chips are mixed with heterogeneous materials such as resin, glass fiber, and copper plating. Copper plating has good ductility and is not easy to break. At the same time, the copper plated through holes further reduce the chip discharge space, and the combined effect of the two makes it more difficult to discharge the chips. The thickness of copper plating is an important factor affecting hole blockage, and excessive copper plating thickness can directly cause insufficient chip space. Starting from increasing the chip removal space, Liu Xiaohua et al. achieved the complete elimination of micro hole back drilling blockage by reducing the copper plating thickness of through holes and performing back drilling post-treatment. However, this method is limited by customers' requirements for hole copper thickness and has a limited scope of application.

 

 

From a mechanical perspective, spindle speed, feed rate, drill tip angle, and drill bit wear all affect the shear force of the drill bit. When the shear force is insufficient, the copper plating cannot be effectively cut, forming continuous and difficult to break chips, which can lead to hole blockage. Experiments have shown that delayed chip removal at low feed rates can increase the clogging rate; Large diameter drill bits have better chip removal capabilities due to larger chip removal grooves; Under the same copper plating thickness conditions, a larger back drilling depth actually results in a lower blockage rate. Wang Xiaoping et al. found through extensive slice analysis that the micro drill transverse edge has no cutting effect, and its main effect on the copper hole is compression. When the hole position deviates and the transverse edge approaches and participates in the copper hole cutting, the compression intensifies, thereby inducing hole blockage. This understanding provides important ideas for the subsequent discussion of the status of back drilling processing based on different situations.

 


In terms of tool optimization, WC has become the main material for back drilling micro drills due to its excellent wear resistance, high rigidity, extremely low coefficient of thermal expansion, and high fracture strength. The A129BD back drilling tool produced by Jinzhou Company adopts a short blade length, small helix angle, and thin core thickness design, which has been tested to significantly reduce the problems of back drilling blockage and deviation. The drilling tip angle also has a significant impact on cutting and chip removal performance. Compared with a regular 165 ° drilling tool, the back drilling special tool with a 130 ° drilling tip angle has a significantly reduced hole blockage rate, basically solving the problem of hole blockage.

 

Factors and Control of Backdrilling Positioning Accuracy

 

The reduction of the back drilling hole diameter leads to a corresponding decrease in the diameter of the drill bit, which reduces the bending strength and centripetal force of the drill bit. It is easy to slip during drilling, resulting in random displacement of the drilling position and a decrease in positioning accuracy. The wear caused by continuous drilling can also weaken the cutting accuracy. The use of cover plates has been proven to be an effective means of improving positioning accuracy. The lubricating resin in the aluminum cover plate can adhere to the micro drill to provide lubrication and reduce micro drill wear; High rigidity drill bits combined with small feed rates can suppress drill bit oscillation. The relevant experiment uses aluminum sheets and phenolic resin sheets stacked as cover plates, while taking into account both positioning and lubrication requirements.

 


In terms of the influence of processing parameters on hole displacement, researchers used a combination of BP neural network and orthogonal experiments to obtain the optimal processing parameters for a 0.35 mm micro drill, which are spindle speed of 150 krpm, hole limit of 1800 holes, and feed speed of 115 ipm. An effective neural network model was established to guide actual production. Li Zhiyuan et al. further pointed out that the positioning accuracy increases with the increase of spindle speed, tool retraction speed, and drill bit diameter, but decreases with the increase of feed rate, drilling number, and inlet plate thickness. However, there is still relatively little research specifically focused on the accuracy of back drilling positioning. The change in positioning accuracy will alter the contact state between the back drilling cutting edge and the material, thereby affecting the axial force during drilling. This relationship requires more in-depth mechanical analysis.